Showing posts with label griniding mill. Show all posts
Showing posts with label griniding mill. Show all posts

Thursday, September 16, 2010

Rugby Cement – ball mill drive shaft recovery0comments

Following a journal failure on a 40-tonne/hour cement ball mill at RMC’s cement plant in Rugby, Metalock Engineering UK, Coventry orbitally machined the badly scored shaft to clean up enabling a new white metal bearing to be fitted and the mill returned to production with minimum disruption.

The Rugby Works ball mill had been operational for over 35 years and was due for replacement, indeed the new machine was on order, but the journal failed before the new mill was due for delivery. The mill is the last on the production line and blends and grinds clinker and gypsum together with other additives to make cement. As production could not be suspended until the new mill arrived, the Rugby Cement management team called in Metalock to discuss the situation and a possible solution.

Metalock’s recommendation was to orbitally machine the 1200mm diameter, 600mm long journal and remove sufficient material to clean up the shaft. This was accepted and following removal of 3mm from the diameter, the mill was re-assembled using a new white metal bearing to suit the revised shaft dimension.

Orbital machining involves having the cutting tool revolve around a stationary shaft. To achieve this at Rugby Cement, the inner bearing ring of the orbital turner was attached to a temporary bearing housing on the ball mill casing with the outer bearing supported on a temporary shaft extension. The rotating cutting tool head was driven via a hydraulic motor.

Orbital turning is just one of the services Metalock offers as part of its on-site machining capabilities. Others include milling, grinding and boring, all using specialist portable machine tools that the company has designed and built. This latest application demonstrated Metalock’s ability to provide solutions in emergency situations and enable a customer to resume production quickly and efficiently.

Commenting on the Metalock operation Julian Ward, Plant Maintenance Engineer at Rugby said that they knew the mill was reaching the end of its life but hoped it would remain in production until the new one arrived. “It didn’t, but Metalock’s expertise helped us out of a spot and got us back into production with minimum delay and disruption”, he added.

In a typical ball mill orbital turning operation the inner bearing ring of the orbital machine is attached to a temporary bearing housing on the ball mill casing with the outer bearing supported on a temporary shaft extension.

Tuesday, August 24, 2010

ball mill how to work

1、A preface

Since in 1880 in industrial production ceramic grinding materials used since the ball more than 100 years history, despite a few advanced countries due to material technology development and only used in ceramic production only plays the ball mill ingredients (mixed), but most of the countries in ceramic production is widely used for grinding mill with mixed casting glaze ceramic raw materials, and paints. However, the efficiency of the ceramic production of ball mill is lower -- about 1 %, so that a large amount of energy consumption. According to statistics, ceramic production in about 40 percent of the energy consumption in the ball grinding process. The ball mill process of material of particle shape and size distribution, the fineness, physical and chemical properties, production efficiency has important influence, this paper will be of ball mill process of related problems were discussed. The superficial

2 、the crushing mechanism of materials

Material in the ball mill process is shattered due to its body and abrasive abrasive results. However, the grinding process is extremely complex. If a single particles as research object, the ball mill process it may repeatedly by grinding compressive stress, which exists in the role of the particles on the surface of a new generation of inherent or expansion crack, and lead to its broken or plastic deformation. When the particles are constantly shattered. A certain level of new particles can be further ground, because the new particles on the surface of the crack, and appear a certain minimum fracture risk of crack stress reduced ACTS. When breaking process continues, the final for crushing stress could increase to make granules of plastic deformation degree. Now, with the plastic deformation, particle size is the will. Thus, when the materials are a grinding size limit. For raw materials, quartz can be ground for 1 micron in size limit, and as the extremum, limestone for 3 ~ 5 micron. That is, when the grinding materials into the scope of ultra-fine grinding mill, the effect was more difficult. In most of the grinding system has a real grind limit, this limit the main on grinding particles produced products, and the tendency to accumulate accumulate and broken up between the physical balance. Therefore, a long ball grinding extended time is meaningless, only leads to increased energy, because the meticulous grain can effectively storage needed to crack expansion of elastic energy.

The actual grinding process than the above discussion, the situation is much more complex particle surface crack expanding and new crack appear because each particle interaction among cracks, the sub-tissue particles interact with the wall, the function, the secondary role between particles and the effect with abrasive particles, particle physics and chemistry of the smell of particles and abrasive environments and aggravate, particle breaking. But, for the recognition of the essence of the visual sense or only on the basis of reasoning.